Seametrics IP82B Fixed Depth Insertion Paddlewheel Meter 6" to 8"

SeaMetrics

MSRP: Kč11 381,44
Kč9 544,89
(You save Kč1 836,55 )
(No reviews yet) Write a Review
SKU:
IP82B
Weight:
4.50 LBS
Shipping:
Calculated at Checkout
x
IP80-Series Insertion Paddlewheel Flow Sensor

APPLICATIONS
  • Industrial water/wastewater treatment
  • Cooling water monitoring
  • Industrial fluid control
  • Chemical proportioning

FEATURES
  • Low-friction, long-life jewel bearings
  • One moving part
  • Fully field-repairable
  • Choice of materials for compatibility with variety of chemicals
  • Fits 1/2? to 8? pipe
  • Fixed depth in fitting ensures proper placement in pipe

GENERAL INFORMATION
The IP80-Series are impeller (or ?paddlewheel?) insertion meters designed for use with a wide variety of liquids in pipe sizes 1/2" to 8". Sensors are available in brass, 316 stainless
steel, PVC, and polypropylene. Bodies are machined from a solid rod for maximum precision. High-quality jewel bearings and nickel-bound tungsten carbide shafts are used for extreme low friction and long life. Low-flow performance is good, although other Seametrics flow meters are recommended where extremely low flows are being measured.
The rotation of the rotor is detected by a non-drag Hall-effect sensor. Output is a current-sinking pulse (square wave), which can be sent long distances (up to 2,000 feet) without a transmitter. This signal can be connected directly to PLC's, counters, and computer cards, as well as a variety of Seametrics controls and displays.
Seametrics IP meters are ideal for chemical proportioning applications. If no display is required, a simple divider such as the PD10 provides adjustable pump pacing. For rate and total display, the FT415 (battery powered) or FT420 (loop powered) flow indicator can be mounted directly on the IP80-Series meter, or remotely on a wall or panel. The AO55 blind analog transmitter can be used to convert to a 4-20 mA output. IP meters are also compatible with the DL76 data logger and FT520 batch processor.
The IP80-Series require special fittings that ensure correct depth placement in the pipe. Fittings come in a variety of materials for compatibility with specific applications. Tee fittings
are individually wet-calibrated at the factory and marked with the K-factor (pulses per gallon). Saddle fittings must be field-installed on the pipe and do not come wet-calibrated. K-factors for saddles are based on factory-testing.

SPECIFICATIONS
 Materials: Sensor Body  Brass, 316 Stainless Steel, PVC, or Polypro
 Rotor  PVDF
 Shaft  Nickel-bonded tungsten carbide (Ceramic optional)
 Bearings  Ruby jewel
 O-Ring  EPDM (Viton optional)
 Rotor Pickup  GMR (Giant Magnetoresistive) Sensor
 Maximum Pressure  Brass / 316 SS / PVC or Polypro (See Pressure vs. Temp. Chart)200 PSI (14 bar) / 250 PSI (17 bar) / 175 PSI (12 bar) @ 75? F
 Maximum Temperature  200? F (93? C) / 200? F (93? C) / 130? F (55? C)
 Flow Range  0.3 - 30 ft./sec.
 Accuracy  +/- 1.5% of full scale
 Signal
 Hall effect current sinking pulse
 Power  6-24 Vdc, 2 mA
 Maximum Current  20 mA
 Cable  #22 AWG, 3 Cond, 18 foot (maximum 2000? run)
x
x
IP82B Fixed Depth Insertion Paddlewheel Meter 6" to 8"