Stenner ECON FP Series Metering Pump, E20PH, High Output, 80 PSI

Brand New! Stenner Econ FP Series Peristaltic Pump. Multiple Control Features and Variable Speed.
Multifunction All-In-One Pump

The Econ FP peristaltic metering pump has all the features found in a microprocessor-controlled system at a fraction of the cost.
This new pump is feature rich, simple in design and very easy to setup.

Features:

• Activated by a softener valve, water meter, flow switch or other flow activated equipment
• Accepts dry contact or 12-24 VAC/VDC signal
• Enclosed housing
• Self-priming, does not lose prime or vapor lock
• Pumps off-gassing solutions and can run dry
• 3-point roller design assists with anti-siphon
• Tube replacement without tools
• Output reproducibility
  

Water Meter Control:

The pump has a built-in pump control module that accepts pulsed input from a water meter with a mechanical read switch.
For each pulse received the pump will turn on from 0.1 to 1 second or 0.5 to 5, 1 to 10, 2 to 20 or 6 to 60 seconds per pulse

Flow Switch Control:

When connected to a mechanical flow switch the pump will accept a contact closure input to start and stop the pump. Speed
is controlled by pre-programming the pump to a selected speed from 10% to 100%. Alternatively, you can use any dry contact
as an input for start/stop control, like a relay or external on/off switch located in a remote location.

24 Volt AC Input Control:

When the pump sees a 24 VAC input signal it will run from 10% to 100% of its rated speed. This works just like the flow switch
input control. This start/stop signal voltage is found on many water softeners and other types of equipment.

Easy Tube Replacement:

Slide cover up to access tube and rollers.
Pull out old tube, inspect rollers, clean housing
Install a new tube, replace cover and lock and
that's it. Easy tube replacements.

Specifications:

• Flow Rate Output Control: Six button control panel with LCD display
• Reproducibility: ±2%
• Maximum Working Pressure: 80 psi (5.5 bar)
• Maximum Operating Temperature: 104°F (40°C)
• Maximum Suction Lift: 25 ft (7.6 m) vertical lift, based on water
• Motor Type: 24VDC, brushless
• Shaft RPM (average maximum): 60
• Duty Cycle: Continuous
• Motor Voltage: 120V 60Hz (0.25A), 230V 60Hz (0.17A), 230V 50Hz (10W), 24VDC (0.85A)
• Power Cord Type: 120V 60Hz, 230V 60Hz: SJTOW, 230V 50Hz: H05RN-F, 24VDC pigtail
• Power Cord Plug End: 120V 60Hz NEMA 5-15P, 230V 60Hz NEMA 6-15P, 230V 50Hz CEE7/7, 24VDC pigtail
• Power Cord Length: 6 ft (1.8 m), 10 ft (3.05 m) or 24VDC Pigtail 1 ft (30.5 cm)
• Classification: Indoor/outdoor

MATERIALS OF CONSTRUCTION

• All Housings: Polycarbonate
• Pump Tube & Check Valve Duckbill: Santoprene®* (FDA approved)
• Pump Head Rollers: Polyethylene
• Suction/Discharge Tubing, Ferrules: Polyethylene (FDA approved)
• Tube and Injection Fittings: PVC or Polypropylene (both NSF listed)
• Connecting Nuts: PVC or Polypropylene (both NSF listed)
• Suction Line Strainer and Cap: PVC or Polypropylene (both NSF listed); ceramic weight
• All Fasteners: Stainless steel

Optional Mounting Accessories:

• 3 Connecting nuts 1/4"
• 3 Ferrules 1/4" or 6 mm Europe
• 1 Duckbill check valve
• 1 Weighted suction line strainer 1/4" or 6 mm Europe
• 20' Roll suction/discharge tubing 1/4" white or UV black OR 6 mm White Europe
• 1 Additional pump tube
• 1 Manual

EC303 Tank Mounting Kit for Stenner Tanks

EC304 Wall Mount or Base Mounting Kit