![Lakos ILB Series Sand Separators, Carbon Steel Hydrocyclone Centrifugal-Action Separators for Low-Flow Applications Lakos ILB Series Sand Separators, Carbon Steel Hydrocyclone Centrifugal-Action Separators for Low-Flow Applications](https://cdn11.bigcommerce.com/s-xxofluljba/images/stencil/448x448/products/68549/62526/Image-3__94912__71734.1708006373.jpg?c=1)
![Lakos ILB Series Sand Separators, Carbon Steel Hydrocyclone Centrifugal-Action Separators for Low-Flow Applications Lakos ILB Series Sand Separators, Carbon Steel Hydrocyclone Centrifugal-Action Separators for Low-Flow Applications](https://cdn11.bigcommerce.com/s-xxofluljba/images/stencil/160w/products/68549/62526/Image-3__94912__71734.1708006373.jpg?c=1)
Lakos
Discontinued: See SMP Series
Discontinued: Replaced by the SMP Sand Master Plus.
Sand is commonly found in water coming from well water systems, surface water systems like rivers, lakes and irrigation canals. These deposits can plug system piping, fixtures, sprinkler heads and drip emitters. The Lakos SandMaster Centrifugal Separator is a perfect solution for this problem. The device, when installed, will remove the sand, silt, and grit particles that are deposited in water. Cannon Water Technology, Inc. is one of the leading distributors of this centrifugal separator sand removal system in the US. The SKU of this product is H2O.
Specifications of Lakos SandMaster Centrifugal Water Filter
The H2O series meets the following specifications:
Model |
Flow Range (GPM) |
Inlet / Outlet |
Dry Weight (lbs.) |
Height/ Diameter |
H20-05 Discontinued |
5-10 |
1/2″ |
7.0 |
19/3/16″ / 4-1/2″ |
H20-10 Discontinued |
10-20 |
3/4″ |
8.0 |
19/3/16″ / 4-1/2″ |
H20-20 Discontinued |
20-30 |
1″ |
13.0 |
24-3/4″ / 6″ |
H20-30 Discontinued |
30-48 |
1 1/4″ |
13.0 |
24-3/4″ / 6″ |
H20-45 Discontinued |
45-70 |
1 1/2″ |
13.0 |
24-3/4″ / 6″ |
Beneficial Features of the Lakos SandMaster Sand Separators
Working of the Centrifugal Separator Sand Removal System
Here is a step-by-step working of the SandMaster sand separators:
The pump passes the water containing sand, grit, and silt flows into the SandMaster.
Centrifugal action in the SandMaster throws the particles to its perimeter. The particles then fall in the lower chamber and get collected there.
The water is now free from contaminants, such as grit, sand, and silt. This clean water then exits the separator and is passed to the pressure tank.
The separated particles are flushed by opening the valve periodically.
Very Important: It is important to know the flow rate prior to selecting the system.
How to Calculate the Well System Flow Rate
As a part of preparation, you need to be ready with a 1 or 5 gallon bucket, and a watch. Following the simple steps below will help you calculate your system flow rate.
Corrosion Warning
Be it any water system, it is likely to face problems like corrosion. The Lakos SandMaster Sand Separator(H2O) series is made from carbon steel material. Thus, while you select this model of sand separator, you should take into account the water quality. Check if the pH level is less than 7.2. If so, it is recommended to increase the pH level. This will reduce the chances of corrosion on the carbon steel material, and hence will make your equipment durable. Pin-hole leaks might occur, if the water that you use is acidic. If adjusting the pH to neutral is not possible for you, then it is advisable to use SMP Series or ILS Series separators that are made from stainless steel material. Cannon Water Technology carries pH neutralizers that can be easily installed on your water system. Please contact us for more information on how to prevent corrosion of your system piping.